Protect Your Hands

PIP offers the widest range of Seamless Cut-Resistant gloves and sleeves anywhere in the world. Cut-Resistant products are extensively used in industrial, construction and food processing markets. The use of Cut-Resistant gloves and sleeves has increased considerably over the years as we've led with the introductions of new yarns and grips.

SHOWING 1-11 OF 11 ITEMS
1 of 1
FILTERS:
CLEAR ALL
G-Tek® KEV™
NeoFoam Coating

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Blended Glove with NeoFoam® Coated Palm & Fingers - Touchscreen Compatible

09-K1218

  • Engineered Kevlar Yarn
  • Gray Shell
  • 18 Gauge High Dexterity
  • NeoFoam Coated Grip
  • Touchscreen Compatible
  • Silicone Free
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X31C

EN 388 2016 Results: 4X31CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI Contact Heat Level: 2

Test Method: ASTM F1060-18
Temperature: 284°F

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

en-407
Protective Gloves Against Thermal Hazards: X1XXXX

Resistance to Flammability - X
Contact Heat Resistance - 1
Convective Heat Resistance - X
Radiant Heat Resistance - X
Resistance to Small Splashes of Molten Metal - X
Resistance to Large Splashes of Molten Metal - X

EN 407 is a general European standard designed to be used for any glove that is to be sold as providing protection against thermal hazards. All six tests are graded on a scale from 0 to 4, with 0 signifying that the glove failed the test, and 4 demonstrating it has achieved the maximum resistance in that specific area.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Kevlar with Polyurethane Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® / Elastane Glove with Polyurethane Coated Flat Grip on Palm & Fingers

09-K1250

  • Kevlar/Elastane Seamless Knit
  • Yellow 15 Ga Shell
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4231B

EN 388 2016 Results: 4231BX

Abrasion: 4
Cut (Coupe Test): 2
Tear: 3
Puncture: 1
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Crinkle Finish Latex

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Glove with Latex Coated Crinkle Grip on Palm & Fingers

09-K1300

  • 100% Kevlar
  • Premium Grade
  • 7 Gauge
  • Medium Weight
  • ANSI A4 EN 5
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3544D

EN 388 2016 Results: 3544DX

Abrasion: 3
Cut (Coupe Test): 5
Tear: 4
Puncture: 4
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Crinkle Finish Latex

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Glove with Latex Coated Crinkle Grip on Palm & Fingers

09-K1310

  • 100% Kevlar
  • Superior Grade
  • 10 Gauge
  • Medium Weight
  • ANSI A3 EN 4
  • SIZES: S-XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

2444C

EN 388 2016 Results: 2444CX

Abrasion: 2
Cut (Coupe Test): 4
Tear: 4
Puncture: 4
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Solid Nitrile Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Glove with Nitrile Coated Smooth Grip on Palm & Fingers - Medium Weight, DISCONTINUED

09-K1400

  • 100% Kevlar
  • Solid Nitrile
  • Smooth Grip
  • 10 Gauge
  • Medium Weight
  • EN Cut Level 3
  • SIZES: XS-XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

2342B

EN 388 2016 Results: 2342BX

Abrasion: 2
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Solid Nitrile Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® / Elastane Glove with Nitrile Coated Smooth Grip on Palm & Fingertips - Medium Weight

09-K1450

  • Kevlar and Elastane Blend Shell
  • 15 Gauge
  • Medium Weight
  • Flat Nitrile Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 12 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3221B

EN 388 2016 Results: 3221BX

Abrasion: 3
Cut (Coupe Test): 2
Tear: 2
Puncture: 1
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Solid Nitrile Grip BEST SELLER

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

09-K1600

  • Engineered Kevlar Yarn
  • Yellow/Black Bumblebee Shell
  • 13 Gauge
  • Black Nitrile Foam Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-3XL
  • PACKED: 6 Dozen/Case
ansi-A7
ANSI Cut Level: A7

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X32F

EN 388 2016 Results: 4X32FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 2
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

ANSI Contact Heat Level: 2

Test Method: ASTM F1060-18
Temperature: 284°F

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Solid Nitrile Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

09-K1618

  • Engineered Kevlar Yarn
  • Gray Shell
  • 18 Gauge High Dexterity
  • Black Nitrile Foam Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4421C

EN 388 2016 Results: 4421CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 2
Puncture: 1
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI Contact Heat Level: 2

Test Method: ASTM F1060-18
Temperature: 284°F

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Kevlar with Solid Nitrile Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

09-K1630

  • Engineered Kevlar Yarn
  • Gray Shell
  • 13 Gauge
  • Black Nitrile Foam Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X31D

EN 388 2016 Results: 4X31DX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

ANSI Contact Heat Level: 2

Test Method: ASTM F1060-18
Temperature: 284°F

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare

G-Tek® KEV™

Hi-Vis Seamless Knit DuPont™ Kevlar® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

09-K1640

  • Engineered Kevlar Yarn
  • Nitrile Foam Coated Grip
  • Palm & Fingertips
  • SIZES: M-XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X31D

EN 388 2016 Results: 4X31DX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Compare
Kevlar with MicroFinish Nitrile Grip

G-Tek® KEV™

Seamless Knit DuPont™ Kevlar® Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers - Medium Weight

09-K1660

  • Seamless Knit Kevlar Shell
  • 13 Gauge Yellow
  • Black Double Dipped Nitrile with MicroSurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4343B

EN 388 2016 Results: 4343BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 3
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
SHOWING 1-11 OF 11 ITEMS
1 of 1
pin Rep Finder
Compare ()
Clear All Compare
Okay, Got it.
X

ORDER SAMPLE

X

GET FIELD TRIAL